Each manual tends to be unique to the manufacturer and usually includes models for a given range of years. It is also worth noting that a snowmobile repair manual may comprise of more than one model for a particular manufacturer. The repair manual is usually purchased as a hard copy or downloaded as an electronic pdf document particularly for the newest snowmobile models.
The Yamaha FX Nytro manual is arranged in a logical order, with the table of content that highlights the various sections of the manual. The manual begins with the general information concerning the snowmobile such as the engine serial number ESN and how to locate the vehicle identification number VIN. Moreover, this section highlights the specifications for the oil and gas along with the ratio of gas to oil to be used.
The general information section also contains warning icons or lights and their meaning and diagnostic codes chart which helps in identifying problems. Each of these subsections provides illustrations with a complete set of equipment and tools required to work on the snow-machine along with safety information.
The Yamaha FX Nytro repair manual provides step-by-step illustrated guidelines to the user on how to perform different repairs.
Some of these repairs include how to align the tracks, how to rebuild the carburetor, replacement of the brake pads chain-case, water pump belt and drive as well as driven clutches.
Such illustrations make it easy for the user to understand and perform repair with ease. It also provides guidelines to the users on how to rebuild the engine, install the transmission, and how to remove and replace gas and coolant tanks.
The manual also provides guidelines on how to perform regular maintenance which begins by highlighting a period maintenance specification.
A Page If there is any question about a service procedure, it is imper- ative that you contact a Yamaha dealer for any service information changes that apply to this model. This policy is intended to provide the customer with the most satisfaction from his snowmobile and to conform to federal environmental quality objectives.
Comprehensive explanations of all installation, removal, disassembly, assembly, repair and check procedures are laid out with the individual steps in sequential order. The manual is divided into chapters. Page All service technicians should be familiar with this entire chapter. Regularly check the brake fluid level and add fluid if necessary. Turn the handlebar slightly to the right and left. Because of this, clutch engagement speed and shifting speed also decrease and unable to maximize the engine output power.
To maxi- mize the engine output, tuning for increasing clutch engagement speed and shifting speed is necessary. Shifting tends to become somewhat easier. When installing, make sure the shock absorber pump lever is down as shown in the illustra- tion. The air pressure of the shock absorbers can be adjusted using the shock absorber pump included with your snowmobile.
This shock absorber pump has low pressure gauge and high pressure gauge Low pressure gauge measuring range If the slide rail suspension bottoms too easily, increase the air pressure by 34 kPa 0. When making adjustments, do it in a small increments. Also, in general, making just one adjustment may not correct the problem. You may need to make several small adjustments to get the best overall results. Handlebar holder bolt: 23 Nm 2. During installation, pay attention to the fol- lowing.
Properly install the rubber seal onto the drive chain cover, making sure that there are no gaps. Be sure to install the collars in their origi- nal positions, otherwise the brake disc and secondary shaft will stick. Collar Bushing Front limiter strap Track clip installer: YSC outside 4.
Place the track in the chassis. For track with a direction of rotation mark Install the track with the mark pointing in the direction of track rotation. Page 15 Nm 1. After all of the bolts are fully loosened, remove them. Page with the recommended lubricant Recommended lubricant: Engine oil 2.
Crankcase bolt 1st: 15 Nm 1. Crankcase bolt 24 Nm 2. If this function detects a malfunction in the system, it immediately operates the engine under substitute characteristics and the warning light and self-diagnostic warning indicator on the upper LCD flash to alert the rider that a malfunction has occurred in the system.
Torque 10 mm 6 mm specifications for special components or assem- 12 mm 8 mm blies are included in the applicable sections of 14 mm Apply engine oil to the bolt thread and both sides of the washer. Tighten the eight bolts to 25 Nm 2. Loosen all the bolts one by one following the tightening order and then tighten them to 25 Nm 2. Spider and sliding sheave Left-hand thread.
Apply engine oil to the bolt thread. Loosen and retighten the bolt to 60 Nm 6. Page SPEC Wire harness Fuel injection system sub-wire harness coupler Speed sensor coupler To the radiator fan motor Fasten the speed sensor lead to the frame rear cross member with the plastic band. To the starter motor assembly Flange bolt 23 Nm 2. Route the DC back buzzer lead above the guide and route the wire harness under the guide. Chocolate G This manual is also suitable for: fx nytro fx10mtx fx nytro fx10rtrx fx nytro fx10mtrx fx nytro fx10rtx fx nytro fx10rtrax fx nytro fx10mtrax.
Print page 1 Print document pages. Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account? Sign up! Restore password. Upload manual. Upload from disk.
0コメント